# Mark Low Height Areas in Navigation Mesh

**URL:** <https://forums.unrealengine.com/t/mark-low-height-areas-in-navigation-mesh/465180>\
**Category:** AI\
**Tags:** ai-navigation, settings, navigation-mesh, unreal-engine, question\
**Created:** [May 14, 2020, 12:28pm UTC](https://forums.unrealengine.com/t/mark-low-height-areas-in-navigation-mesh/465180 "2020-05-14T12:28:45Z")\
**Posts on this page:** 3\
**Page:** 1

<div class="post-metadata">

**Author:** ![Strik3One](https://d3kjluh73b9h9o.cloudfront.net/original/4X/2/8/5/28502927f1d97ba1051b3b47ccfe17233bf41ef0.png) [@Strik3One](https://forums.unrealengine.com/u/Strik3One)\
**Post date:** [May 14, 2020, 12:28pm UTC](https://forums.unrealengine.com/t/mark-low-height-areas-in-navigation-mesh/465180/1 "2020-05-14T12:28:45Z")

</div>

Hello,

I was looking trough the options for the Navigation Mesh and discovered the option “Mark Low Height Areas”. This seemed to be perfect as I my game will allow the AI agents to crouch.

However, when checking the box nothing changes, no NavArea\_LowHeight is being generated under anything and I cannot seem to affect these area’s either by placing down Nav Modifier Volumes.

Are there additional things I have to set up in order to get this to work?

Thanks

---

<div class="post-metadata">

**Author:** ![samuelthomson](https://d3kjluh73b9h9o.cloudfront.net/original/4X/2/8/5/28502927f1d97ba1051b3b47ccfe17233bf41ef0.png) [@samuelthomson](https://forums.unrealengine.com/u/samuelthomson)\
**Post date:** [September 17, 2021, 12:19pm UTC](https://forums.unrealengine.com/t/mark-low-height-areas-in-navigation-mesh/465180/2 "2021-09-17T12:19:21Z")

</div>

Any progress on this?

---

<div class="post-metadata">

**Author:** ![Cznico](https://d3kjluh73b9h9o.cloudfront.net/original/4X/2/8/5/28502927f1d97ba1051b3b47ccfe17233bf41ef0.png) [@Cznico](https://forums.unrealengine.com/u/Cznico)\
**Post date:** [July 2, 2026, 4:39pm UTC](https://forums.unrealengine.com/t/mark-low-height-areas-in-navigation-mesh/465180/3 "2026-07-02T16:39:49Z")

</div>

For anyone who is trying to figure it out in 2026 this is my approach:

Part 1 — Create NavArea\_Crouch

1. Content Browser → pick a sensible folder.
2. Right-click → Blueprint Class.
3. Expand All Classes, search NavArea. Select NavArea as the parent (if it’s not selectable, pick NavArea\_Default — both are walkable by default). ⚠ Do not pick NavArea\_LowHeight or NavArea\_Null — those are non-traversable.
4. Name it NavArea\_Crouch.
5. Open it → Class Defaults and set:

- Default Cost = 2.0 — walkable but pricier than open ground, so bots only duck through when it’s genuinely the better route.
- Draw Color = something loud (e.g. bright orange or cyan) — this is what you’ll finally see in the nav overlay to confirm it worked.
- Leave everything else (the walkable AreaFlags are inherited — you can’t/shouldn’t edit them).

1. Save.

Part 2 — Enable Mark Low Height Areas project-wide (covers all maps)

Edit → Project Settings → Navigation Mesh.

1. Under Generation, expand the Advanced rollout (the little arrow at the bottom of the section).
2. Tick Mark Low Height Areas = True.
3. This writes to DefaultEngine.ini, so all maps’ RecastNavMesh pick it up.

Part 3 — Place a NavModifierVolume over a passage (per passage, per map)

1. Place Actors panel → search Nav Modifier Volume → drag it into the level near your passage.
2. Position and scale it so it fully encloses the crouch gap — from at/below the floor up past the low ceiling, covering the whole passage footprint. It must overlap the low-clearance region (err on the side of slightly larger).
3. In its Details → Nav Modification:

- Area Class = NavArea\_Crouch
- Area Class To Replace = NavArea\_LowHeight ← this is the magic; it auto-switches the volume into the “low pass” mode that keeps the low voxels.
